Operator’s ManualIMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYMTD PRODUCTS INC. P.O. BOX 361131 CLEVELAND, OHIO 44136-9722PRINTED IN U.S.A.W
10BLADE CONTROL HANDLEThe blade control handle is located on the upper handle of the mower. See Figure 5 . The blade control handlemust be depressed i
11CUTTING HEIGHT ADJUSTMENT LEVER (Model 960 thru 969)The rear wheel cutting height adjustment lever is located above the left rear wheel. To adjust t
12Figure 7To charge the battery, remove the protective cap from the end of the battery pack lead. Plug charger lead intobattery pack lead and then ins
13TO STOP ENGINE AND BLADE• Release the blade control handle to stop the engine and the blade.WARNING: The blade continues to rotate for a few seconds
14SECTION 9: ADJUSTMENTSWarning: Do not at any time make any adjustment to lawn mower without first stopping engine anddisconnecting spark plug wire.
15Note:For some operators, the drive clutch handle may not be in a comfortable position. You can adjust the handleby tightening or loosening the adjus
16DECKThe underside of the mower deck should be cleaned after each use to prevent a build-up of grass clippings,leaves, dirt or other matter. If this
17When sharpening the blade, follow the original angle of grind as a guide. It is extremely important that eachcutting edge receives an equal amount o
18DRIVE BELT REMOVAL AND REPLACEMENTStep 1. Disconnect the spark plug wire and ground it against the engine.Step 2. Drain the fuel tank or place a p
19Step 13. Squeeze the belt together and push belt forward. Press the control arm inward towards the deck and remove the six speed cable from the s
2SECTION 1: FINDING YOUR MODEL NUMBERThis Operator’s Manual is an important part of your new walk behind. It will help you assemble, prepare andmaint
20SECTION 11: LUBRICATIONWARNING: Always stop engine and disconnect spark plug wire before cleaning, lubricating or doingany kind of work on the lawn
21Blade Control: Lubricate the pivot points on the blade control handle and the brake cable at least once aseason with light oil. See Figure 11. The b
22SECTION 13: TROUBLE SHOOTING GUIDE Refer to separate engine manual packed with your mower for more engine related information.NOTE: For repairs bey
23Models 950 thru E969Ref.No.Part No. Code Description1 712-3025 Hx. Jam Nut 5/16-242 736-0425 Bell Wash. .325 x .930 x .0453 756-0656 Pulley4 7
24Models 950 thru 959158Pulley Assembly forreference onlyTransmission and pulleyfor reference only
25Ref.No.Part No. Code Description1 710-0134 Scr. Carr. 1/4-20 x .622 710-0654A Scr. TT:3/8-18:1.003 710-0703 Scr. 1/4-20 x .7504 712-0397 Wing Nut 1/
26Models 960 thru E969848Pulley Assembly forreference onlyTransmission and pulley for reference only
27Ref.No.Part No. Code Description1 710-0134 Scr. Carr. 1/4-20 x .622 710-0654A Scr. TT:3/8-18:1.003 710-0703 Scr. 1/4-20 x .7504 712-0397 Wing Nut 1/
28Models E9693940513729162118202322171924A2625A28271043141530224735153912114241475546385054474445521351
29Model E969Ref.No.Part No. Code Description1 710-1174 Bolt Cur. Carr. 5/16-18 x 2.0 2 714-0104 Cotter Pin .072 x 1.12 Lg.3 720-0241 Knob Assembly 4
3SECTION 3: SLOPE GAUGEWARNINGDo not mow on inclines with a slope in excess of 15 degrees (a rise of approximately 2-1/2 feet every 10 feet). A ridi
30Models 950 thru 96976A28272913141530224153153118162118202322171924A2625Ref.No.Part No. Description1 710-1174 Bolt Curv. Carr. 5/16-18 x 2.0 2 714-01
31Models 950 thru E969Ref.No.Part No. Code Description1 746-0939 6 Spd. Cable2 656-0613 Pulley Ass’y Mult - Spd.3 710-0167 Scr. 1/4-20 x .50 Carr.4 71
MANUFACTURER’S LIMITED WARRANTY FOR:For TWO YEARS from the date of retail purchase within the United States of America, its possessions andterritories
4SECTION 4: IMPORTANT SAFE OPERATION PRACTICESWarning: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOTFOLLOWED, COULD ENDANGER THE
5footing, RELEASE THE BLADE CONTROL HANDLEIMMEDIATELY and the blade will stop rotating withinthree seconds.• Mow only in daylight or good artificial l
6worn). Replace with blade which meets originalequipment specifications listed in this manual.• Keep all nuts, bolts, and screws tight to be sure thee
7SECTION 5: UNPACKING INSTRUCTIONSREMOVE UNIT FROM CARTON• See Figure 3.• Remove staples, break glue on top flaps, or cut tape at carton end and peel
8SECTION 6: SET-UP INSTRUCTIONSThis guide covers two model series. Models 950 thru 959 have fixed front wheels; models 960 thru 969have caster front
9• Your mower has been shipped in the lowest cutting position for shipping purposes. Please see the “cuttingheight adjustment lever” section on page 1
Comments to this Manuals